Apple II series
Originally designed by Steve Wozniak, the Apple II series was both one of the first mass-market 8-bit microcomputers and the longest-lived. The machines exemplified Wozniak's design sensibilities of not including hardware when software can perform the same function, and of being wide open for expansion. Elements of the II's design influenced many later computers; PCs today have expansion slots in part because the Apple II did, for instance.
Assuming you don't have the Software List library, you can use MAME like any other Apple II emulator with the disk images you already have. For the II, II Plus, IIe, IIc, and IIGS, you can boot a 5.25" disk by using the command line switch -flop1. For example, "mame64 apple2e -flop1 Dung_Beetles.dsk". For the IIc Plus and IIGS, you can boot a 3.5" disk image by using the switch -flop3. For example, "mame64 apple2gs -flop3 FTA_Nucleus.2mg".
- Apple II (1977 - driver name apple2)
- - The original machine. Includes a 6502 CPU, 8 expansion slots, up to 48KiB of RAM on the motherboard, cassette and game controller I/O, a 1-bit speaker clicker, and video modes including 40x24 text, 40x48 16-color "lo-res" graphics, and 6 color (8 but there's two blacks and two whites) 280x192 "hi-res" graphics. In addition, lo or hi-res graphics could be displayed along with 4 lines of text at the bottom.
- Apple II Plus (1979 - driver name apple2p)
- - Mostly a ROM change; Wozniak's Integer BASIC was replaced with a licensed version of Microsoft BASIC, and the system's firmware was extended to be able to auto-boot from cards with a certain set of signature bytes in their firmware ROM.
- Apple IIe (1983 - driver names apple2e, apple2ee, apple2ep)
- - Condensed a large portion of the previous systems (which were primarily off-the-shelf 74-series TTL chips) into two custom ICs, "IOU" and "MMU". Slot 0, which on the II and II Plus normally contained a 16K "language card" to expand the system to 64 KiB, was eliminated and 64 KiB is on board in a configuration compatible with the language card. The system also supports a second 64 KiB of RAM for a total of 128 KiB, and brings in a series of double-resolution video modes inspired by the ill-fated Apple ///. These include 80x24 text, 80x48 16-color "double-lo-res" graphics, and 560x192 16-color "double-hi-res" graphics.
The IIe was later "enhanced"; this replaced the 6502 CPU with a WDC 65C02 that included additional instructions, and added GUI-drawing characters to the built-in text font. Finally, a "platinum" IIe was released that came in a revised gray case (instead of the previous beige) and had the keyboard expanded to include a numeric keypad.
- Apple IIc (1984 - driver names apple2c, apple2c0, apple2c3, apple2c4)
- - This was an enhanced IIe with 128 KiB of RAM packed into a small "pizza box" style form factor. Because there was no room for slots, the IIc included hardware equivalent to two serial cards, a mouse card, and a floppy disk controller and drive.
Later versions of the IIc included support for external 3.5" disk drives and a memory expansion slot which provided the equivalent of the 1 MiB Apple II Memory Expansion Card.
- Apple IIGS (1986 - driver names apple2gs, apple2gsr0, apple2gsr1)
- - The 16-bit Apple II. Built around a WDC 65C816 CPU (which had a full 65C02 emulation mode) running 3 times faster than earlier machines, the IIGS is 99% compatible with the enhanced IIe but was also capable of running new 16-bit software that could directly access up to 8 MiB of RAM. The ROMs included a full optimized 65C816 port of the Macintosh's Toolbox APIs and Mac apps written in Pascal or C could be ported over with almost no code changes. The IIGS introduced the concept of switchable slots, where each of the 7 slots could be switched between a built-in function and using a card plugged into the slot. This provided the integration of the IIc combined with the expandability of the IIe.
Built-in hardware included two serial ports, a detachable keyboard and mouse supported by the then-new Apple Desktop Bus (ADB), 5.25" and 3.5" floppy support, a 32-oscillator Ensoniq sample-playback synthesizer chip, and new video modes: 320x200 "Super Hi-Res" with 16 unique colors per horizontal line, and 640x200 "Super Hi-Res" with 4 unique colors per scanline. Unlike previous Apple IIs, these new modes were not built on NTSC trickery and provided real full-color images with no bleeding or other artifacts.
- Apple IIc Plus (1988 - driver name apple2cp)
- - This was a final-configuration IIc (with the memory expansion slot) with the internal 5.25" disk drive swapped for a 3.5" one and a licensed copy of the 4 MHz Zip Chip accelerator included.
The default configurations
MAME defaults to configuring these systems to run the widest variety of software "out of the box".
- Apple II and II Plus: 16K Language Card in slot 0, Mockingboard in slot 4, Disk II controller and 2 drives in slot 6.
- Apple IIe: 128 KiB RAM installed, Mockingboard in slot 4, Disk II controller and 2 drives in slot 6.
- Apple IIc: Mockingboard 4C (third-party add-on which gives a Mockingboard in slot 4) is installed. -ramsize may be used to include up to 1 MiB of expansion RAM on the later models.
- Apple IIGS: 1 MiB of expansion RAM is installed, which allows running all known software. Stereo output is included (it was optional on the real system). 2 each of 3.5" and 5.25" drives are included.
- Apple IIc Plus: -ramsize may be used to include up to 1 MiB of expansion RAM.
To find out what a version of MAME supports for configurable slot and port devices, run MAME with the -listslots parameter on the commandline. The Apple II and II Plus have 8 slots, which are "sl0" through "sl7" plus a game port. The IIe has 8 slots, "sl1" through "sl7" plus the "aux" slot and the game port. The IIgs has "sl1" through "sl7", while the memory slot is handled through the "ramsize" switch. For instance, "-ramsize 4M" on the IIgs gives you 4 megabytes of RAM.
Slot 0 on the II and II Plus can have the following cards:
- lang is the standard 16K Apple Language Card. This is installed by default, giving you a 64K system.
- ssram is the Saturn Systems 128K card, which is compatible with the language card and has additional RAM for programs which can use it.
Slots 1-7 on the II, II Plus, IIe, and IIgs generally support all of these cards:
- diskii is the standard Apple 2-drive floppy controller. This is the old-style not-very-accurate version but it may work with some marginal disk images that the default controller does not.
- diskiing is the new cycle-perfect Disk II controller. This one supports .WOZ images, including copy-protected ones. This is in slot 6 by default on the II, II Plus, and IIe.
- diskiing13 is the cycle-perfect Disk II controller with the old 13-sector PROMs installed, so it can boot DOS 3.2 13-sector disks without running BOOT13 from the DOS 3.3. System Master.
- mockingboard is the Mockingboard music/sound card supported by some games. This is in slot 4 by default on the II, II Plus, and IIe.
- phasor is the Applied Engineering Phasor music/sound card, which is back compatible with the Mockingboard but has extended capabilities supported by e.g. Ultima V.
- alfam2 is the ALF Apple Music II 9-voice music/sound card. I don't believe any games supported it, but I could be wrong.
- aesms is the Applied Engineering Super Music Synthesizer. It's not compatible with any other cards, but if you can find the software for it it can be fun for a few minutes.
- cffa2 is the CFFA2 SD/IDE card for the Apple II. This version has 65C02 firmware so it will only work properly on the enhanced IIe and IIgs. This works with most standard Apple II hard disk images.
- cffa202 is the CFFA2 SD/IDE card with plain 6502 firmware which works on the II, II Plus, and unenhanced IIe.
- memexp is the Apple II Memory Expansion Card, sometimes called "Slinky". It has 1 megabyte populated, and is automatically recognized by most versions of AppleWorks.
- ramfactor is the Applied Engineering RamFactor card, which is mostly a clone of the memexp card.
- thclock is the ThunderWare ThunderClock Plus, which is automatically recognized and used by ProDOS.
- softcard is the Microsoft Z80 SoftCard, which lets you run CP/M.
- applicard is the PCPI AppliCard, which also runs CP/M but at a much faster speed since it uses on-card RAM instead of sharing the Apple's. The AppliCard also works on the Apple /// driver. It does require the specific AppliCard startup disk.
- videoterm is the Videx VideoTerm 80-column card for the II and II Plus.
- aevm80 is the Applied Engineering ViewMaster 80 80-column card. This is their enhanced clone of the Videx VideoTerm.
- ap16 is a German clone of the Videx VideoTerm 80-column card.
- ap16alt is the same German clone of the Videx VideoTerm with a different firmware version.
- vtc1 is yet another VideoTerm clone, this one of unknown origin.
- ultraterm is the Videx UltraTerm 80 and 132-column card for the II, II Plus, and unenhanced IIe.
- ultratermenh is the Videx UltraTerm 80 and 132-column card with special firmware to work on the enhanced IIe.
- ssc is the Apple Super Serial Card.
- swyft is the IAI SwyftCard, which works only on the IIe and turns it into Jef Raskin's original dream for the Macintosh. By modern standards it's quite weird to use.
- themill is the Stellation Two The Mill card, which adds a 6809 processor and enables running Microware OS-9.
- sam is the optional card for the S.A.M. Software Automated Mouth software speech synthesizer. It gives a higher-quality voice than the normal Apple II speaker output.
- arcbd is the Third Millenium Engineering Arcade Board, which added ColecoVision-like graphics and sound capability to the Apple II.
- midi is the standard Passport/Yamaha style MIDI card supported by most 8-bit MIDI software and GS/OS (with the "Card 6850 MIDI" driver).
- zipdrive is the Zip Technologies Zip Drive, an IDE card from the ZipChip accelerator company. No relation to the later Iomega Zip Drive. This card requires a custom partitioned/formatted hard disk image and so is mostly of interest to people who owned such a card and want to image their old drive and use it under emulation.
- focusdrive is Focus Technologies' version of the zipdrive IDE card. The same caveat about custom hard disk images applies.
- echoiiplus is the Street Electronics Echo II Plus hardware speech synthesizer. This works with a lot of accessibility software for the Apple II and some games.
- scsi is the Apple II Revision C SCSI Card. It supports standard hard disk and CD-ROM ISO and BIN/CUE images as well as MAME's CHD format.
- mouse is the Apple II Mouse Card for the II, II Plus, and IIe. This is useful for mouse-compatible software like Dazzle Draw, Apple II DeskTop, and MousePaint.
- parallel is the Apple II Parallel Card.
- corvus is the Corvus Systems "flat cable" hard disk interface. This is very difficult to set up on the Apple II; I've gotten it to boot DOS 3.3 off the hard disk, but unless you were an expert on these things back in the day it's for curiosity only.
- mcms1 and mcms2 are the 2 cards of the Mountain Computer Music System. They must be placed in adjacent slots or MAME will not start up. These cards give the Apple II wavetable synthesis capability, which was used as part of the Alpha Syntauri system.
- dx1 is the Decillonix DX-1 sampler card. Currently this doesn't do much because MAME doesn't have audio input support.
- tm2ho is the Applied Engineering TimeMaster II H.O. clock/calendar card. The optional X-10 home control feature is not supported in MAME.
- ezcgi is a graphics/sprites card from a design published in BYTE Magazine.
- ezcgi9938 and ezcgi9958 are extended versions of the ezcgi card with the TMS9938 and TMS9958 GPUs.
- ssprite is the Synetix SuperSprite graphics and sound card, which has similar capabilities to the Arcade Board and the EZ-CGI.
- ssbapple is the SSB Apple speech card. This only works with its own software to my knowledge, it wasn't as widely supported as the Echo II line.
- twarp is the Applied Engineering TransWarp accelerator card. This works to run e.g. AppleWorks at faster speeds without unthrottling MAME and making typing difficult.
- vulcan is the Applied Engineering Vulcan IDE card. This requires a custom partitioned/formatted hard disk image; the software to set that up is reasonably easy to find, but it's intended primarily for users who had the card in their real Apple II.
- vulcangold is the Gold version of the Vulcan IDE card. The firmware we have for it currently only works on 65816 CPUs and so this card is only an option on the IIgs.
- 4play is the 4 Play Joystick Card, which gives you 4 players in compatible software (primarily NinjaForce's Bomberman clone for the IIgs).
- ceyes2 is the ComputerEyes/2 video digitizer (added in 0.214), which gives higher-quality digitization results than the game port version.
The IIe auxiliary slot supports these cards:
- ext80, the Apple IIe Extended 80-Column Card. This gives the IIe 128K of RAM and enables double-hi-res and double-low-res video modes. This is in the IIe auxiliary slot by default.
- std80 is the Apple IIe 80-Column Card. This gives 80-column text, but will not work with software that requires 128K of RAM or uses the double-hi-res or double-low-res video modes.
- rw3 is the Applied Engineering RamWorks III, which gives the IIe 128K of RAM, double-hi and -low res video modes, plus 8 megabytes of expansion RAM which later versions of AppleWorks can use.
The -ramsize switch controls the amount of RAM on many machines. This defaults to 48K on the II and II Plus, 64K on the IIe, 128K on the IIc and IIc Plus, 1.25 MB on the ROM 0 and 1 IIgs, and 1 MB on the ROM 3 IIgs.
- The Apple II can be set to 4K, 8K, 12K, 16K, 20K, 24K, 32K, 36K, or 48K.
- The II Plus can be set to 16K, 32K, or 48K.
- The IIe only can be set to 64K.
- The original IIc only can be set to 128K, but the memory expandable IIc can be set to 128K, 384K, 640K, 896K, or 1152K. The additional RAM is usable by AppleWorks.
- The IIc Plus, Laser 128, and Laser 128 EX2 all can be set to 128K, 384K, 640K, 896K, or 1152K, just like the memory expandable IIc.