Driver:InterPro: Difference between revisions

From MAMEDEV Wiki
Line 2: Line 2:


The Intergraph InterPro brand name refers to a range of computers featuring the CLIPPER processor, and running CLIX, a port of UNIX System V release 3.1.
The Intergraph InterPro brand name refers to a range of computers featuring the CLIPPER processor, and running CLIX, a port of UNIX System V release 3.1.
[[File:2400.jpg|200px|thumb|right|A dual-screen InterPro 2430]]


== Status ==
== Status ==

Revision as of 10:52, 17 July 2018

Intergraph InterPro

The Intergraph InterPro brand name refers to a range of computers featuring the CLIPPER processor, and running CLIX, a port of UNIX System V release 3.1.

A dual-screen InterPro 2430

Status

The MAME driver for the InterPro is a work in progress, and is currently capable of booting and running the CLIX operating system and some software for the InterPro 2020 configuration. Some other models are capable of booting the diagnostic monitor and disk-based diagnostic utilities, but not yet able to install or run CLIX.

Hardware

Models

The InterPro range consists of 5 distinct generations or families, named after gemstones. The system models within each family share a common architecture and features, usually differing only by CPU type and clock speed.

System Families
Year Family Models CPU I/O Processor
1986 Amethyst 32C/100/200
300
C100 80186
80386
1988 Topaz 3000/4000/5000 C300/C300Plus 80386
1990 Emerald 6000/6100/6200/6500
6600
C300/C300Plus
C4
1990 Turquoise 2000 C300
1992 Sapphire 2400/6400
2500/2700/2800/6700/6800
C4T
C4I

For Emerald, Turquoise and Sapphire systems, the four-digit model number encodes some aspects of the original system configuration, and breaks down as follows.

Model Numbering
Position Purpose Values
1 Case 2=desktop, 6=minicase
2 CPU 0=C300, 4=C4T, 6=C4, 5/7/8=C4I
3 Graphics 0=none, 3=MMG, 5=GTDB, 4=EDGE-1, 8=EDGE-2
4 Backplane 0=standard, 5/7/9=?
InterPro minicase

As examples using this encoding, an InterPro 2020 is a desktop C300 system fitted with MMG graphics, while an InterPro 6880 is a minicase C4I system with EDGE-2 graphics. Systems configured without graphics are typically fitted with a serial terminal, and branded InterServe rather than InterPro. This model numbering and branding applies to the system cases, but of course changing graphics options will cause a system's software-identified model number to change.

Cards

SMT094, an EDGE-2 Plus graphics card

A range of approximately 150 installable cards were produced for the InterPro family. The most common and important of these included the system mainboards and several different graphics options, however a range of less common cards supported functions such as video capture, SCSI expansion, networking and a VME bridge were available. Desktop InterPro systems support the installation of two cards in addition to the main board, using an interface referred to as CBUS. Larger systems supported either 5 or 12 slots with an interface referred to as SRX, which is physically incompatible with CBUS.

Regardless of type, card names are typically prefixed by the letter M, followed by PCB or SMT (the latter designation indicating a surface-mount board), followed by a 3-digit board type. Boards are also typically marked with a single alphabetic revision number and an ECO (engineering change order) level recording hardware-level fixes.

Examples include MPCB963, which is described as "2000 Graphics f/1 1Mp Monitor", and MSMT094, which is an "EDGE-2 Plus Processor f/1 2Mp-FB".

Keyboard

InterPro keyboard
InterPro keyboard layout
InterPro keyboard layout

Configuration

Machine configuration

Diagnostics

Installing CLIX